CONFIGURING THE METER

USING SETPOINT 1 CONFIGURATION ("S1.CF")
Setpoint 1 Configuration (S1.CF) is not active unless your meter has dual relay output capabilities. The LED's will display whether the ("S1.CF") is active or not. You may use Setpoint 1 Configuration ("S1.CF") for the following:
    * Setting setpoint's active band above or below your chosen value
    * Selecting whether the setpoint operation is latched or unlatched
    * Assigning setpoint values to the net or gross reading
Setting Setpoint 1's Active Band
1. Press the MENU button until the meter shows "S1.CF".

2. Press the /TARE button. The meter shows one of the following:
* "S.1=A" (Active above the deadband) (default)
* "S.1=B" (Active below the deadband)

3. Press the /NT/GRS button to toggle between available choices.

4. Press the /TARE button to select if Setpoint 1 is latched or unlatched or press the MENU button to store your selection and enter "S2.CF" (Setpoint 2 Configuration)

Selecting if Setpoint 1 is Latched or Unlatched
1. Press the /TARE button. The meter shows one of the following:
* "S.2=L" (setpoint 1 to be latched) (default)
* "S.2=U" (setpoint 1 to be unlatched)

2. Press the /NT/GRS button to toggle between available choices.

 3. Press the /TARE button to assign Setpoint 1 values to net or gross reading or press the MENU button to enter "S2.CF" (Setpoint 2 Configuration).

Assigning Setpoint 1 Values to Net or Gross Readings
1. Press the /TARE button. The meter shows one of the following:
* "S.3=N" setpoint 1 assigned to net reading (default)
* "S.3=G" setpoint 1 assigned to gross reading

2. Press the /NT/GRS button to toggle between available choices.

3. Press the MENU button to store your selection(s). The meter momentarily shows "STRD", followed by "S2.CF" (Setpoint 2 Configuration).

USING SETPOINT 2 CONFIGURATION ("S2.CF")
Setpoint 2 Configuration ("S2.CF") is not active unless your meter has dual relay output capabilities. The LED's will display whether the ("S2.CF") is active or not. You may use Setpoint 2 Configuration ("S2.CF") for the following:
    * To set setpoint's active band above or below your chosen value
    * To select whether the setpoint operation is latched or unlatched
    * To assign setpoint values to the net or gross reading
Setting Setpoint 2's Active Band
1. Press the MENU button until the meter shows "S2.CF".

2. Press the /TARE button. The meter shows one of the following:
* "S.1=A" (Active above the deadband) (default)
* "S.1=B" (Active below the deadband)

3. Press the /NT/GRS button to toggle between available choices.

4. Press the /TARE button to select if Setpoint 1 is latched or unlatched or press the MENU button to store your selection and enter "S1.DB" (Setpoint 1 Deadband)

Selecting if Setpoint 2 is Latched or Unlatched
1. Press the /TARE button. The meter shows one of the following:
* "S.2=L" (setpoint 1 to be latched) (default)
* "S.2=U" (setpoint 1 to be unlatched)

2. Press the /NT/GRS button to toggle between available choices.

3. Press the /TARE button to assign Setpoint 2 values to net or gross reading or press the MENU button to enter "S1.DB" (Setpoint 1 Deadband).

Assigning Setpoint 2 Values to Net or Gross Readings
1. Press the /TARE button. The meter shows one of the following:
* "S.3=N" (setpoint 2 assigned to net reading) (default)
* "S.3=G" (setpoint 2 assigned to gross reading)

2. Press the /NT/GRS button to toggle between available choices.

3. Press the MENU button to store your selection(s). The meter momentarily shows "STRD", followed by "S1.DB" (Setpoint 1 Deadband).

SETTING THE SETPOINT 1 DEADBAND ("S1.DB")
Setpoint 1 Deadband ("S1.DB") is not active unless your meter has dual relay output capabilities. The LED's will display whether the ("S1.DB") is active or not. The Setpoint 1 default deadband is 0003. To change the deadband (hysteresis) of setpoint 1, follow these steps:

1. Press the MENU button until the meter shows "S1.DB".

2. Press the /TARE button. The meter shows the last previously stored 4-digit number (0000 through 9999) with flashing 4th digit.

3. Press the /NT/GRS button to change the value of the flashing digit. If you continue to press the /NT/GRS button, the flashing digit's value continues to change.

4. Press the /TARE button to scroll horizontally to the next digit.

5. Press the MENU button to store your selection. The meter momentarily shows "STRD", followed by "S2.DB" (Setpoint 2 Deadband).

SETTING THE SETPOINT 2 DEADBAND ("S2.DB")
Setpoint 2 Deadband ("S2.DB") is not active unless your meter has dual relay output capabilities. The LED's will display whether the (S2.DB) is active or not. The Setpoint 2 default deadband is 0003. To change the deadband (hysteresis) of setpoint 2, follow these steps:

1. Press the MENU button until the meter shows "S2.DB".

2. Press the /TARE button. The meter shows the last previously stored 4-digit number (0000 through 9999) with flashing 4th digit.

3. Press the /NT/GRS button to change the value of the flashing digit. If you continue to press the /NT/GRS button, the flashing digit's value continues to change.

4. Press the /TARE button to scroll horizontally to the next digit.

5. Press the MENU button to store your selection. The meter momentarily shows "STRD", followed by "OT.CF" (Output Configuration).
Help Price List Specifications Print Manual Manuals Home
 Home Home  Table of Contents TOC  Back Back  Next Next